Sisteme training tehnic | ED

• One-stop training kit for embedded system, DSP and FPGA
• 7” Wide TFT LCD, 10/100 Ethernet 1Port, Serial 1Port, SD/MMC, ATA and other interfaces

 

• Analog feedback loop & DC servo system
• Modularized by the function of servo circuits
• Overload protection for the servo amp's and power supply's output

 

• 19 types of modules & graphic boards
• 25 types of electrical machine assembly
• Experimental board rack & storage trolley

 

• Measurement of induction motor’s power efficiency
• How to use electro-dynamometer
• Torque Measurements by dynamometer
• Use of separately excited DC generator

 

• RIM’s no-load power factor and load power factor
• Load characteristics of separately excited DC shunt-wound generator
• No-load saturation characteristics of generator
• DC shunt-wound generator’s loss and power factor

 

• Start and Sync characteristics of synchronous motor
• V-curve characteristics of synchronous motor
• Synchronous motor’s loss and efficiency
• Load characteristics of self-excited shunt-wound generator

 

• DC motor’s load characteristics
• DC motor’s loss and efficiency
• Alteration of the motor’s rotative directions
• Motor’s speed and torque

 

• Load characteristics of shunt-wound and compound generators
• Generator’s speed and output by winding type
• Loss and efficiency comparisons by winding type

 

• Start and load characteristics of squirrel cage induction motor
• Alteration of the rotative directions of squirrel cage Induction Motor
• Slip speed and torque of induction motor
• Induction motor’s no-load power factor and load power facto

 

• Load characteristics of DC compound motor
• Cumulative compound and differential compound characteristics
• Generator’s rotating speed and output characteristics
• Loss and efficiency of DC compound generator

 

• Complete Motor/Generator Training System
• Various load characteristics(Resistance, L/C Reactance and Torque)
• Selectable System(ED-5100-1, ED-5100-2, ED-5100-3 or Full Set)

 

• Inverting, Non-inverting and Differential Amplifiers
• Comparator Circuit
• Voltage and Current Circuit

 

• Remote mode by PC and Local mode by manual operation on the panel
• Graphical display of diagrams on panel for AD/DA conversion procedures
• DSO embodiment by A/D Converter for collection and analysis of analog data on PC
• Storage of measured data and generation of 5 wave forms required for experiments through D/A Converter

 

• Modular system with experimental rack
• Pulse Generation, synthesis and conversion
• Built-in signal source and DC power supply

 

• Capable of performing Logic monitoring functions
• Graphical presentation of functional diagram on each module
• 15 modules each for TTL or CMOS IC type

 

• Unique logic cards(TTL/CMOS)
• Internal pulse outputs
• 3-stage Logic Monitor
• BCD indication

 

• Hexadecimal number indicators
• Selectable pulse outputs
• Built-in DC power supp

 

• Hi/Lo Logic Switch
• BCD hexadecimal indication LED
• Built-in DC power supply(+5V,+9V,±15V)
• Voltage and current meter
• DC overload alarm and indication
• Variable and single pulse generator

 

• OP-Amp. characteristics and various appplication circuits
• Main Frame contains DC Power Supply, AF Signal and Frequency Counter

 

• SCR characteristics
• Rectifier and phase control
• Trigger and gate control
• Motor speed control

 

• AF Generator and Frequency Counter(built-in)
• Dual DC Power Supply(5/6V, 9/12/15V)
• Decade Capacitor(2 digits) and Programmable Resistor

 

• 24 Experimental Boards in two sections : (A) Semiconductor and (B) Electronic Circuit
• Experimental Board rack and board storage cabinet

 

• Realistic arrangement of materials used for contact sequence
• Indication of each element’s symbol on the panel

 

• Covers essential circuits needed to practice power electronics circuits
• Modular type with aluminum carrying case
• Optional rack to be customized upon requst

 

• 14 experimental boards with mounting rack and storage cabinet
• Analysis of DC and AC circuits
• Electromagnetics experiments

 

• Various types of circuit experiments with 17 basic modules plus 3 optional modules
• Main console(power supply) and storage cabinet

 

• 5 experimental modules for power electronics covering basic theory and applied experiments
• Capable of real-time measurements on PC by linking it to CBIS-1400 model
• By connecting PC to the Docking station, contact control is implemented on MMI(HMI) based software
• Report on experimental results & electronic manual on PC

 

• 15 experimental modules for basic electricity/electronics and analog & digital circuits
• Capable of real time measurement on PC by linking it to CBIS-1400 model.
• By connecting PC to the Docking station, contact control is implemented on MMI(HMI) based software
• Report on experimental results & electronic manual on PC

 

• PC-based multi-function instrument for electricity/electronics and other experiments
• Digital Storage Oscilloscope with the 2-channel simultaneous 50MS/s sampling rate
• Spectrum Analyzer functions using Digital Storage Oscilloscope(DSO)
• Variable Power Supply(VPS), Function Generator(FG), Analog Output and Digital Output
• Analysis of collected data on PC through the modules of DSO, DMM, FC and Analog/Digital Input
• Numerical and graphical indication of the data measured and analyzed in real time

 

• DC Amplifier
• Complementary Amplifier
• Differential Amplifier
• Operational Amplifier
• Active Filter Circuit

 

• Basic to advanced learning courses for Embedded Linux
• Intel PXA255(400MHz) high-performance microprocessor
• 6.4TFT LCD, Ethernet 2port, Serial 3port, PCMCIA/CF/MMC interfaces
• FPGA Chip(Altera Cyclone 120,000Gate) mounted for SoC experiments
• Reliable hardware and abundant experiment contents for programming

 

• Foundation for the Ubiquitous System Build
• Intel PXA 270 high performance processors
• 6.4TFT LCD, Ethernet 3Port, Serial 3Port, PCMCIA/CF/MMC interfaces
• FPGA Chip Altera Cyclone 4,000 LEs(12,000 LEs Option) for SoC courses
• Processor Core Board & CMOS Image Sensor

 

• Conversion processing experiments on the produced energy(power production / processing)
• Energy efficiency experiments followed by energy production and conversion
• Voltage and current characteristics curve
• Standalone or integrated operation of the energy experimental module
• Enriched teaching aids such as simulation software for power production

 

• Conversion experiments on the produced energy(power production/processing)
• Characteristics of Solar Cell module’s voltage and current
• Alarm beep for wrong wire placement
• Voltmeter and ammeter as included for measuring AC and DC
• Control by PC and waveform and graph output

 

• Inverse current protection
• Built-in charge controller and bulit-in battery
• Overcurrent/electric discharge protection
• 360° rotation by the direction of wind
• Configurable composite structure by adding optional

 

• Fuel cell generation using photovoltaic
• Complete disassembly and assembly of the fuel cell
• Current and voltage measurement for PEM Fuel Cell Stack according to each of Cell
• Power production experiment using PEM Fuel cell

 

• Testing of load for maximum four fuel cell at the same time
• Removable type of electrical dissolution and fuel cell from main body
• Monitoring through LabVIEW program

 

• Practice basic method how to operate such as basic peration, Constant voltage, Constant current, serial connection, and arallel connection
• Brightness control, Color control, and lighting
• Simulation for Steady/PWM

 

• Home network based experiments suitable for ubiquitous computing
• Integrated ubiquitous device using ZigBee/RFID and finger print recognition
• Designed to help develop home network on the ground of Lon Protocol
• Equipped with each PLC module(Power Line Communication) for home network
• Related experiments through Neuron C and MICOM programming

 

• Designed to help develop network devices on the basis of Lon Protocol
• Control of each device installed in the field through power line communication
• Related experiments through Neuron C and MICOM programming
• Home network control in utilization of LabVIEW

 

• Home network control in liaison with Embedded PXA 255/270/272/320
• Power line communication and ZigBee modules with Multi Port in use together
• Embedded

 

• The optional Embedded System(ED-255EK) can be linked as a gateway
• ZigBee network can be built using TinyOS, F8WOS
• Capable of control and monitor through Ethernet
• The RFID Card Reader is supplied as a standard shipped component for applied experiments on security, home automation and robot

 

• The electronic manual operable on PC comes with ED-1450 and e-learning is optimized by remote control of student’s operating program and evaluation of student’s online report in real time.
• Through DS-1410, it provides Variable Power Supply(VPS), Function Generator(FG), Analog Output, Digital Output needed for experiments.

 

• Various types of test point for Air-interface experiments
• Anti-collision function
• OCX Library useful for application engineers
• 13.56MHz I-CODE Type in common usage
• Capability of reading and writing data on Tag

 

• F/W program practices for RFID Reader
• 13.56MHz and 900MHz in common use
• Data Read/Write to 900MHz Tag
• ED-3710 application programming (13.56MHz, 900MHz)
• Fixed Type RFID Reader

 

• Panel type structure for good grasp of entire network configuration
• Learning about the functions and characteristics of basic network equipments such as NIC, HUB, Router and DSU, plus installation and maintenance
• Interlocking experiments with Internet for clear understanding a real network
• Capable of conneting to the open network on campus

 

• Study of functions, characteristics, installation, repair and maintenance of basic ADSL components such as Telephone Exchange, Splitter, DSLAM, ADSL Modem, HUB and LAN Card
• Network structure through interworking experiments with Internet and capability of Internet usage and simple programming
• Capable of interworking experiments with ED-NET-3(LAN Training System)

 

• Step by step courses on the networks theories to train the engineers
• CISCO Router based training will help obtain CCNA, CCNP, CCIE certificates
• Functions and characteristics of network system(LAN Card, Router, L2 Switching Hub, L3 Switching Hub)
• 19Rack type structure for effective network configuration
• Optimized learning system for the Router based on one on one training(OPTION)

 

• Rich experiments devoted to IS95 standard
• Easy-to-follow structure as main functions are itemized in modules

 

• The Electronic Manual operable on PC comes with ED-1440 and e-learning is optimized by remote control of student’s operating program and evaluation of student’s online peport in real time.
• Through DS-1410, it provides Variable Power Supply(VPS), Function Generator(FG), Analog Output, Digital Output needed for experiments.

 

• Interlocking system package with CBIS-1400 and DS-1410 Models (Options)
• Experiments on a measurable low frequency bandwidth
• Realistic experiments on modulation and demodulation
• Verification of the output waveform on PC engaged with CBIS-1400 Model

 

• Modularized by each communicarion type
• PAM, PTM, PCM, DPCM, ADPCM, LDM, ADM, Delta-sigma
• No need to have additional generators (built-in power supply and signal source)
• Can display the test point and measure signals using an oscilloscope

 

• 10 experimental modules with a mainframe console
• Basic concepts on the communication systems
• Experiments on the broadcast frequency band tuning
• Generation of AM and FM waves and detection theory

 

• 7 experimental modules with a mainframe console
• Harmonic Analysis and Superheterodyne Receiver experiments
• PCM(TDM), Sample Hold, and Delta Modulation experiments

 

• Modularized by the function of digital communication circuits
• FSK, ASK, PSK, QPSK and digital communication principles
• 12 types of modules including a power supply unit

 

• E/O and O/E conversion and characteristics
• Optical PCM communication(trasmission&reception)
• Optical Data communications using personal computer
• DC power supply, a roll of fiber cable and the microphone included as peripherals

 

• PLL and Digital Synthesizer
• PAM, PCM, FDM and FSK Modem
• 10types of module including DC Power Supply

 

• Gunn Oscillator base system
• Directional Coupler & Horn Antenna
• Frequency : 9GHz~11GHz (X-Band)
• Microwave output : 15mV

 

• 16 different types of Antenna
• RF source generation : 500MHz, 2GHz and 10GHz
• Software simulation of radiation Patterns and characteristics of Antenna
• Antenna Directional Coupler (Manual / Remote)

 

• Helps understand theories on the Microstrip Line Theory and Microwave Elements Design
• Composed of 22 types of modules such as VCO using Coupler, Divider, Circulator, Attenuator and Filter
• SWR Detector, Modulation, Transmission/Reception, Detector, Self-Oscillation functions

 

• HF band(3.5~12MHz)
• Transmitter and Receiver modules for each circuit stage
• Graphical latour of the block diagrams, plus LEDs and test points
• Covers Push-to-Talk and helps understand short wave communications

 

• Realistic Simulation of FM stereo broadcast
• Graphical layout of block diagrams, display elements and test points
• Covers the principles of FM stereo encoder and decoder
• Experiments on stereo amplifier (equalizer, tone control, pre-amp, etc.)

 

• Best solution for IPTV platform and IPTV Digital Broadcasting System in applications and experiments
• High-performance Microprocessor SIGMA EM8622 for powerful multimedia functions
• IPTV Set-top Box, Media Player, Digital Multimedia Processing

 

• Ideal for the Ubiquitous and Home Network based experiments
• Home security experiments on utilization of its unattended security function
• Robot control API using Visual C++ and control functions by Visual Basic Scripter
• Next Generation Cell(Lithium Lon) – compact size and increase in life time

 

• Omni-directional robot system
• Microprocessor based control command as for simple use
• Floor detecting sensor and forward area detecting distance sensor as mounted
• Mountable expansion by adding the optional ultrasonic sensor and infrared sensor

 

• Integrated sensor training system covering electricity, electronics, automation and chemistry
• Consists of 24 sensor modules, 8 application modules, 5 conversion modules, 2 signal prossing modules, 11 pneumatic components and power supply
• PC-based control for convenient, effective data collection and analysis
• Application module experiments(illumination, pneumatic auto coor, motor, temperature) for enhancing field experiences

 

• Belt-type conveyor simulator
• Control Modes : manual or automatic by programmable Logic Controller
• Three photo sensors and two motion solenoids

 

• Practical training on inverter and 3-phase induction motor operations
• Control experiments using a PLC module (in use of D/A module)
• Feasible contact-type PLC control
• Carrying case type structure for convenient storage and mobility

 

• Experiments on Servo Motor control techniques using Servo Driver
• Aluminum carrying case for convenient storage and mobility
• JOG operation, PLC control operation, PC control operation
• Various types of control elements easily to be mounted
• Capable of checking normal operating voltage / over current by voltmeter and ammeter

 

• Display of the rotational speed and angle data using LCD
• PC control and waveform output functions
• Portable type with Aluminum Carrying Case

 

• Graphical display of functonal block diagram on the system suface
• Real-time monitoring and control by PC Control Program
• LM Guide and Rotary Encoder for position control
• Displays moving distance and angle data using LCD

 

• Aluminum hard case structure for mobility
• Applied experiments on the motor’s rotation characteristics
• AC motor control technology using the inverter
• Interlocking experiments with Programmable Logic Controller

 

• Experiments on various types of special control unit
• Characteristics of Servo Motor and setup of Servo Driver
• Essential components in automation using a PLC position module
• 4mm banana jack to increase wiring capability

 

• Aluminum Profile-based work table structure for mounting the components
• Manufacturing electrical composition elements in modular type using actual components
• Wiring practices and circuit composition to configure sequence composition elements on the working board
• Various contents linked with e-learning such as wiring, operation and etc.

 

• Mountable 5pieces MCU(8051,PIC, ATmega128, ATmega8535, upd78F0547)
• Practice of various communications such as RS-232 USB and Ethernet
• SoC experiments using the default FPGA (EP1C4F324)
• Storage of sensor data display and excel data using UI(LabVIEW)

 

• Mountable 5 type of MCU(8051,PIC, Atmega128, Atmega8535, Upd78f0547)
• Practice of various communications such as RS-232 USB and Ethernet
• Practice from basic I/O exercises to sensor application exercises with 5 MCU’s
• Possible of various practice by using of Bread Board and I/O Expansion Port
• Storage of sensor data display and Excel data using UI(LabVIEW)

 

• Small desk type structure for space optimization
• Built-in DC power supply for convenience
• Handy experiments on the basic and application programming commands
• Base structure capable of expansion by mounting the special modules

 

• Comprehensive experiments on PLC, Inverter, Touch Panel and Sensor
• Various programming experiments including digital numeric value
• Aluminum case structure for convenient storage and mobility
• Built-in DC power supply as part of system for handy practices
• All-in-one training system which comes with the inverter and touch panel

 

• Industrial training enhancement in the field of PLC and sequence control
• Various types of programming experiments covering a digital numeric program
• Aluminum case structure for storage and locomotive convenience
• Built-in DC power supply and built-in expansion port

 

• Composed of essential devices for Programmable Logic Controller I/O commands
• LD (Ladder Diagram), IL (Instruction List), SFC (Sequential Function)
• Built-in Simulator to train on the encoder’s principle and functions
• Stepping motor and DC motor installed as standard (forward/reverse rotation, linear movement)
• Capable of network configuration by CPU and Remote I/C Link

 

• SIMATIC STEP7-300 PLC programming and execution
• Modularization of the devices dssential for PLC I/O commands
• Experiments for basic command and various application program
• Binary data experiments with 4digits digital switch and display unit
• Customizable for various types of STEP7-300 series CPU

 

• MITSUBISHI MELSEC-Q PLC programming and execution
• Modularization of the devices essential for PLC I/O commands
• Experiments for basic command and various application program
• Binary data experiments with 4digits digital switch and display unit
• Various types of QCPU can be selected from a basic to hyper performance

 

• ALLEN-BRADLEY SLC-500 PLC programming and execution
• Modularization of the devices essential for PLC I/O commands
• Experiments for basic command and various application program
• Binary data experiments with 4digits digital switch and display unit
• Customizable for various types of SLC-500 Series CPU upon request

 

• Monitoring of internal data through the 4-digit LED
• LD (Ladder Diagram), IL (Instruction List), SFC (Sequential Function)
• Stepping motor and DC motor installed as standard for rotational / linear movement
• Basic 3 Modules : Input Controller, Output Simulator, Count & Position Simulator

 

• Docking System architecture separating the main body from PLC modules
• Various types of Programmable Logic Controller experiments
• Modular structure for convenient storage and mobility
• Built-in multi connection device compatible with world’s famous PLC brands

 

• Easy-to-use demonstarator for principles of refrigeration/airconditioning
• Motor Compressor : Pison type
• Trouble shooting for pipe leakage

 

• Experiments on the 4-axis Cartesian robot
• Teaching pendant in 7.5wide color touch panel
• Standard language for the international industrial robot
• Simulation software in three dimension

 

• Experiments on the industrial SCARA robot
• Teaching pendant in 7.5wide color touch panel
• Standard language for the international industrial robot
• Simulation software in three dimension

 

• Experiments on the industrial robot being used in real life
• Teaching pendant in 7.5wide color touch panel
• Standard language for the international industrial robot
• Simulation software in three dimension

 

• Disassembly and assembly practices for the robot actuators
• Utilization of a robot being used in the industry, so to apply a job site after graduation
• Simulation software provided to make assembly or disassembly easily
• Enables basic operation and testing practices on the assembled unit using a controller

 

• Control of pressure, flow, level and temperature which are essential for process control
• Capable of stand-alone control and mixed combination in various types
• Real-time measurement and monitoring using data collection and signal conditioning
• Measurement of flow’s status and gain of the controlled data

 

• Organization of various control elements in complexity for applied technology
• Total of 6 processes comprising supply, Sensor, Stopper, Absorption & Transfer, Conveyor and Loading
• Built-in control elements covering mechanics, electricity, and electronics
• Control circuit for simple and high speed data transmission in the USB type

• Small size type suitable for traning on automation system’s installation and operation
• Mechanism and installation methods through assembly and disassembly per process
• Enhancement of application programming techniques through PLC control

 

• Comprehension of basic production automation processes such as transfer, fabrication, classification, inspection and storage
• Convenient wiring and pipe arrangement with a label of each component such as sensors and actuators
• PLC training system function(various types of sequence actions through a change in PLC control program
• Counter/timer function and motor control by PLC or without PLC(electrical method)
• Aluminum profile worktable & control modules for easy mounting

 

• Stores at the cell designated by crane
• Stores according to color and materials
• Selecting and taking at the time of cell is full

 

• Computer-Integrated Manufacturing Training System under the application of advanced control technology for real field experiences
• Capable of “per unit” configuration into the two or more processes, or entire processes for customized experiments by combining each process

 

• Consists of one gripper and 5-axis vertical multi joints
• Absolute-type RVDT Position Sensor applied to each axis and requires no Limit switch
• High performance CPU enables real-time control of each axis
• PID gain tuning and real-time control

 

• Enriched examples for the beginning level to an advanced level in the robot class
• Easy to mount modules by the clamping device
• USB high speed(480Mbps) interface
• Extensive learning for the sensors being used in the field of Ubiquitous and Home Network
• Image processing practice using USB Camera

 

• Obstacle avoidance and autonomous traveling using eight ultrasonic sensors
• Various types of robot configuration by combining each module
• Remote control by the controller
• Precise operation by DC Servo Motor
• Flow chart based programming software

 

• Convenient parts fixation by ‘one-touch lever’ bases and aluminum profile structure
• Efficient space utilization by mounting parts horizontally/vertically
• A complete pneumatic training system to help achieve advanced level of skills and obtain pneumatic engineering related licensesOver