Factory Automation Trainer ED-4031

Cod: ED-4031


 

Brosura produs PDF, 0.65 Mb

Descriere

EXPERIMENTS

  • Configuration elements of factory automation system
  • Characteristics and principles of the object detection sensor
  • PLC(Programmable Logic Controller) control programming
  • Main processes of factory automation system(supply, fabrication, classification, storage)
  • Methods of DC motor control(speed, direction)
  • Mechanical structure and assembly for the factory automation system
  • Utilization of the optional PLC simulation software(EDS-SimPL)

 

Features:

  • Comprehension of basic production automation processes such as transfer, fabrication, classification, inspection and storage
  • Convenient wiring and pipe arrangement with a label of each component such as sensors and actuators
  • PLC training system function(various types of sequence actions through a change in PLC control program
  • Counter/timer function and motor control by PLC or without PLC(electrical method)
  • Aluminum profile worktable & control modules for easy mounting
 

Alte produse ED

PULSE/DIGITAL COMMUNICATION TRAINER ED-2920

• Modularized by each communicarion type
• PAM, PTM, PCM, DPCM, ADPCM, LDM, ADM, Delta-sigma
• No need to have additional generators (built-in power supply and signal source)
• Can display the test point and measure signals using an oscilloscope

 

OP-AMP CIRCUIT TRAINER ED-6000

• OP-Amp. characteristics and various appplication circuits
• Main Frame contains DC Power Supply, AF Signal and Frequency Counter

 

CONVEYOR CONTROL SIMULATION UNIT CU-4001

• Belt-type conveyor simulator
• Control Modes : manual or automatic by programmable Logic Controller
• Three photo sensors and two motion solenoids

 

WOUND-ROTOR INDUCTION MOTOR/ DC GENERATOR MG-5213

• Load characteristics of shunt-wound and compound generators
• Generator’s speed and output by winding type
• Loss and efficiency comparisons by winding type

 

PC BASED ANALOG COMMUNICATION TRAINER ED-1460

• Interlocking system package with CBIS-1400 and DS-1410 Models (Options)
• Experiments on a measurable low frequency bandwidth
• Realistic experiments on modulation and demodulation
• Verification of the output waveform on PC engaged with CBIS-1400 Model

 

LAN TRAINING SYSTEM ED-NET-3

• Panel type structure for good grasp of entire network configuration
• Learning about the functions and characteristics of basic network equipments such as NIC, HUB, Router and DSU, plus installation and maintenance
• Interlocking experiments with Internet for clear understanding a real network
• Capable of conneting to the open network on campus

 

MOTOR / GENERATOR TRAINER UNIT MG-5216

• RIM’s no-load power factor and load power factor
• Load characteristics of separately excited DC shunt-wound generator
• No-load saturation characteristics of generator
• DC shunt-wound generator’s loss and power factor

 

UBIQUITOUS SENSOR NETWORK TRAINER ED-3160

• The optional Embedded System(ED-255EK) can be linked as a gateway
• ZigBee network can be built using TinyOS, F8WOS
• Capable of control and monitor through Ethernet
• The RFID Card Reader is supplied as a standard shipped component for applied experiments on security, home automation and robot

 

PROGRAMMABLE LOGIC CONTROL TRAINER ED-4260

• Monitoring of internal data through the 4-digit LED
• LD (Ladder Diagram), IL (Instruction List), SFC (Sequential Function)
• Stepping motor and DC motor installed as standard for rotational / linear movement
• Basic 3 Modules : Input Controller, Output Simulator, Count & Position Simulator

 

PC BASED DIGITAL COMMUNICATION TRAINER ED-1440

• The Electronic Manual operable on PC comes with ED-1440 and e-learning is optimized by remote control of student’s operating program and evaluation of student’s online peport in real time.
• Through DS-1410, it provides Variable Power Supply(VPS), Function Generator(FG), Analog Output, Digital Output needed for experiments.