Use Extech’s MO53 Pinless Moisture Meter for non-invasive measurements on wood and other building materials with virtually no surface damage. The depth of measurement is approx <0.75" (20mm). Easy-to-operate with display icons that indicate the levels of moisture content plus audible alert feature. Ideal for building restoration projects and applications where moisture detection on floors, tiles and under carpets is critical. A must-have tool for analyzing the after-effects of water leakage behind walls and in ceilings.

Features:

Pinless moisture measurement depth to <0.75" (20mm)
Measures Moisture up to 99.9% for Wood and 56.5% for other building materials
Displays moisture level in wood and building materials such as wall board, sheet rock, cardboard, plaster, concrete, and mortar
Audible Alert - Tone rate beeps faster as the moisture level increases
Icons display low, medium and high levels of moisture content
Easy-to-use, compact-sized design
Data Hold freezes reading on display
Built-in battery level check and measurement verification test
Auto Power Off conserves battery power
Complete with 9V battery and wrist strap

Alte produse EXTECH

EXTECH EX350 MULTIMETRU TRUE RMS CU 11 FUNCTII

• True RMS for accurate AC measurements
• 4000 count backlit LCD display
• Low Impedance (LoZ) prevents false reading caused by ghost voltages
• Low Pass Filter (LPF) for accurate measurements of variable frequency drive signals

EXTECH RT30: WIRELESS AC CIRCUIT IDENTIFIER (914MHZ) WITH EXTERNAL PROBE

• Combines non-contact voltage and light detection with RF (Radio Frequency) transmission technology
• Remotely identifies mid-run AC wiring, circuit breakers, switched lines, AC outlets, and light fixtures
• Non-contact mid-run AC wiring identification without cutting into wires
• Lighting circuit identification using built-in light sensor

EXTECH MG300 MULTIMETRU 13-FUNCTII CU WIRELESS TRUE RMS / REZISTENTA IZOLATIE

• Wireless USB interface transmits measurement data to a PC
• Backlit super large triple display
• 125V, 250V, 500V, and 1000V test voltages
• Insulation Resistance from 0.001MOhm to 4000MOhm
• Auto discharge of capacitive voltage

EXTECH MP530A MULTIPRO® MULTIMETRU PERFORMANT

• High basic DC Voltage accuracy of 0.08%
• Wide AC Voltage bandwidth of 40Hz to 20kHz
• Rugged design with protective holster and water resistant housing
• Backlit 5000 count LCD display for high resolution (0.01mV, 0.1µA, 0.01Ohm, 0.01nF, 0.001Hz)

EXTECH 407730 SONOMETRU DIGITAL

• ±2dB accuracy with 0.1dB resolution
• A+C weighting
• AC analog output
• Record Max/Min values over time
• Utilizes 0.5"(12.7mm) electret condenser microphone

EXTECH 38220 SURSA DE TENSIUNE 18V/3A

• Constant voltage or current
• Dual backlit LCD displays for voltage and current
• Short circuit protection
• Current limiting

EXTECH MN47 MULTIMETRU COMPACT CU 12 FUNCTII

• Built-in Non-contact Voltage Detector (from 100 to 600VAC)
• AC/DC Voltage, AC/DC Current, Resistance, Capacitance, Frequency, Type-K Temperature, Duty Cycle, Continuity / Diode
• Autoranging with manual override
• 4000 count high-contrast LCD display

EXTECH DCP42 SURSA DE TENSIUNE REGLABILA SIMPLA 160W

• Constantly calculates and adjusts the Voltage and Current limit points according to available maximum power (160W)
• At maximum current (10A), voltage is limited to 16V
• At maximum voltage (42V), current is limited to 3.8A
• Dual action rotary encoder control with push knob for fine and coarse tuning

EXTECH ET10 TESTER RECEPTACOL GFCI

• Works with GFCI circuits
• Tests for faulty wiring in 3-wire receptacles: Correct, Open Ground, Open Neutral, Open Hot, Hot/Ground Reverse, Hot/Neutral Reverse
• Lights indicate circuit condition
• Standard North American 3-prong plug

EXTECH LCR200 RLC-METRU PORTABIL

• Measures Inductance, Capacitance, and Resistance with secondary parameter Q (Quality), D (Dissipation), R (Resistance), P (Phase), ESR (Equivalent Series Resistance)
• Simultaneous 20,000/2,000 count backlit display of the primary parameter (L, C or R) with the secondary parameter
• Auto Select measurement function with 1kHz default test frequency
• Five test frequencies
• Set Hi/Lo limits using absolute values or percentage limits