The PSB-2000 series, which is a high power density, programmable and multi-range output DC power supply. There are six models in the series including one power booster unit. The PSB-2000 series has the output voltage of 0~80V and 0~800V, and the output power ranges of 0~400W and 0~800W. The multi-range output functionality facilitates flexible collocations of higher voltage and larger current under the rated power range. Both series and parallel connections can be applied to the PSB-2000 series to fulfill the requirements of higher power output range.

The PSB-2000 series provides three sets of preset function keys to memorize regularly used settings of voltage, current and power that users can recall rapidly. The sequence function, via RS232C, USB interface or optional GPIB interface, can connect with the computer to produce output power defined by sequence of a series of set voltage and current steps that are defined by the computer. This function is often used to establish a standard test procedure for the verification of the influence on DUTs done by the swiftly changing operating conditions.

The PSB-2000 series protects over voltage and over current. The power supply output function will be shut down to protect DUTs while the protection mechanism is triggered to function. When conducting battery charging operation, the Hi-W mode of thePSB-2000 series will prevent reverse current from damaging power supply. The PSB-2000 series provides analog control and analog monitor interfaces on the rear panel to control PSB-2000 output via the external voltage or to externally monitor voltage and current output status of power supply. PSB-2000 panel can be rotated 90 degree angle suitable for vertical or horizontal position to accommodate the ideal space utilization.

Features:

Output Voltage Rating : 80V/800V
Output Power Rating : 400W~800W
Constant Power Output for Multi-Range(V&I)Operation
Series and Parallel Operation(2 Units in Series or 4 Units in parallel Maximum)
Sequence function edited by PC will be controlled through power supply optional interface
Standard Interafce: RS-232C / USB / Analog Control Interface
Optional Interface: GPIB

Alte produse INSTEK

GOODWILL INSTEK PEL-3000 SERIES

• Commands are compatible with Kikusui PLZ-4W model.
• Dynamic(Switching) Function:0.0166Hz ~20kHz
• Soft Start Function:Off / On(1~200ms, Res:1ms)
• Adjustable OCP / OVP / OPP / UVP Setting
• Short Circuit Function

GOODWILL INSTEK APS-9000 SERIES

• Stable and Low-Distortion Output Waveforms
• Software Calibration to Ensure Accuracy
• Panel-Lock Function to Prevent Operation Error
• Frequency,Volt,Amp,Watt and Power Factor Display

GOODWILL INSTEK GUT-6600A

• Easy-Operating Tester, Particularly be Designed for the Digital IC
• Supported Device:74/54/40/45 Serial, Drive 2xxx
• Small, Portable, Light and Power-Saving, Usable With Battery
• Average Search Time: 0.6 Second
• Display: 16 Characters in 1 Line LCD
• Test Pins: 14~24 Pins

ANALIZOR SPECTRAL 9KHZ..3GHZ GW INSTEK GSP-930

• Frequency Range: 9kHz ~ 3GHz
• High Frequency Stability: 25ppb (0.025ppm)
• RBW: 10Hz ~ 10kHz in 1-3 steps, 10kHz ~ 1MHz in 10% adjustable steps
• Phase Noise: -88dBc/Hz @1GHz, 10kHz Offset
• Built-in Measurement Functions: Channel Power, N-dB bandwidth, OCBW, ACPR, SEM, TOI, CNR, CTB, CSO
• Built-in Spectrogram and Topographic Display Modes

GOODWILL INSTEK GOM-802

• 30000 Counts Display
• High Accuracy 0.05%
• Hi/Lo Comparator and Limit Percent Setting
• Measurement of REL, Actual and % Value
• Continuous or Triggered Measurement Mode

GOODWILL INSTEK GCM-403 & GCM-407

• Auto Range, Expect Current Measurement
• Auto Power Off
• Max Hold
• True RMS Measurement (GCM-407)

GOODWILL INSTEK GAD-201G

• Automatic level & distortion measurements
• Auto or Hold function selectable
• 0.1% ~ 100% in 7 distortion measuring ranges
• 20Hz ~ 20kHz in 3 continuous ranges
• 400Hz, 1kHz, 10kHz 3 frequency spots
• 1mVrms ~ 300Vrms in 12 ACV measuring ranges

TRUSA INCERCARI 5KV GWINSTEK GPT-9801 GPT-9802 GPT-9803 GPT-9804

• 200VA AC Test Capacity
• 240x64 Ice Blue Dot matrix LCD
• Manual/Auto Mode
• Controllable Ramp-up Time
• True RMS Current Measurement
• High resolution: 1uA for measuring current, 2V for setting voltage
• Interface : RS-232C, USB device, Signal I/O and GPIB (optional)

GOODWILL INSTEK GSB-01 / GSB-02

• Front & rear input connector design is suitable for the GPT-9800/9900/9900A series
• A maximum of 4 scanner boxes (32 CH) can be connected to one GPT-9800/9900/9900A series
• High-intensity LED for Channel, Status & Judgment indications

GOODWILL INSTEK PPH-1503D & PPH-1506D

• Pulse Current Measurement
• Long Integration Current Measurement
• Sequence Function (Sequential power output)
• Built-in Battery Simulation Function