The Digital Line Analyser EDCT 20 is a hand-held, battery operated, multi-function measuring instrument for in or out-of-service bit error and signal measurements. EDCT 20 can work in both unframed and framed modes for end-to-end and loopback testing of digital channels. It offers features such as: timeslot monitoring; timeslot access; set-ups and result storages. With the installation of the optional data communication unit, EDCT 20 is able to verify the interfaces (V.24, V.35 and V.11) between the DTE (Data Terminal Equipment) and the DCE (Data Communication Equipment), both in synchronous and asynchronous systems. Results can be stored in it's non-volatile memory or logged on PC via USB.

Features:

• 2048 kbit/s framed / unframed transmitter and receiver with through mode capability

• Codirectional (G.703) interface

• 2048 kbit/s slip measurement

• Interface parameters to ITU-T Rec. G.703

• Graphical displaying of signal pulse shape

• Jitter, jitter tolerance and transfer characteristic measurement

• PCM30, PCM30CRC, PCM31, PCM31CRC frame analysis

• nx64 kbit/s testing

• Line signal frequency measurement

• Mux / Demux measurements

• BER test to ITU-T Rec. G.821, G.826, M.2110, M2120

• CAS status analysis

• Analysis of CAS (R1.5, R2) systems

• EDSS1, V5.1/V5.2, QSIG, SS7 protocols

• Auto-configuration function

• PC software for analysis of signalling data and control

Alte produse ELEKTRONIKA

CALIFICATOR RETELE CUPRU CABLU ELEKTRONIKA ELQ30A+

• Analogue measurements on leased or switched circuits 20 Hz to 20 kHz
• Analogue-to-analogue measurements on PCM systems
• Loop holding and dialling (pulse or DTMF) for dial-up circuit testing
• Built-in loudspeaker and microphone, service telephone
• In-service talk/listen and voice monitoring facility

ANALIZOR ISDN ELEKTRONIKA EIT10

• BRI TE and NT simulation, monitoring
• PRI TE and NT simulation, monitoring
• Dual U interface for troubleshooting between the NT and the Exchange
• B-channel voice and D-channel signaling monitor
• EDSS1, V5.1/V5.2, QSIG, SS7 protocols
• Analysis of CAS (R1,5; R2

LOCATOR DEFECTE CABLURI TELECOM TELEFONIE ELEKTRONIKA EFL 10

• Loop resistance measurement
• Resistance difference measurement
• Mutual capacitance measurement
• Conductor-shield capacitance measurement
• Break and split measurement
• DMM functions

TESTER TELEFONIE ELEKTRONIKA ETT 10

• Hand-held programmable instrument with microprocessor control
• Testing of subscriber lines, exchanges and telephone sets
• Hand-held programmable instrument with microprocessor control
• Ring generator for testing telephone sets
• Battery for feeding the telephone line with DC current

TESTER LINII DE DATE DIGITALE ELEKTRONIKA EDCT2A

• CAS status analysis
• Auto-configuration function
• Storage of set-ups and results
• Voice channels monitoring through built in speaker
• External clock input

SET TESTARE NIVEL 6 MHZ LEVEL TEST SET ELEKTRONIKA ET92

• Comfortable End to End Measurements
• High Resolution Spectrum Analyzer
• USB Ports for Result and Setup Transfer
• Memory for Test Setups

ANALIZOR LINII DATE TELEFONIE ELEKTRONIKA ELA10

• Service telephone facility
• Loop holding and dialing (pulse and DTMF) for dial-up circuit testing
• Acoustic pair detection facility
• AC-DC Voltage measurement
• Memory for phone numbers
• In-service talk/listen and voice monitoring

TESTER TELEFONIE COMUNICATII & DSLAM ELEKTRONIKA ETET30

• SIX INSTRUMENTS IN ONE
• DMM LINE TESTER
• EXCHANGE SIMULATOR
• TELEPHONE SIMULATOR
• GOLDEN MODEM
• SPECTRUM ANALYZER
• TDR

CALIFICATOR LINII XDSL XDSL ELEKTRONIKA ELQ2+

• TDR for fault location
• Load coil detection facility
• DC-AC bridge option
• 2.2 MHz frequency range for fix-frequency and spectrum measurements
• Longitudinal voltage protection

TESTER NIVEL LINIE 2,4 MHZ LEVEL TEST SET ELEKTRONIKA ET91

• Psophometer
• Autmatic End to End Measurements
• High Resolution Spectrum Analyzer
• Measuring Bridge
• Memory Locations for Test Setups