Code: Seba-KMT PVS-100
Description
PVS 100
The exact knowledge of the phase assignment in the area of power distribution is an essential requirement for the safe and reliable power network operation. This covers all voltage levels from a low voltage distribution to high voltage transmission systems. A phase identification or verification is required for the determination of load distribution, the control of the phase assignment of old or new installation and prior to switching to avoid damages and outages. The phase identification with the PVS 100 enhances the safety of power distribution systems and prevents accidents.
Key benefits:
All the advantages at a glance
Direct phase indication with a GSM/GPS connection or with an available low voltage connection
Extremely easy input of phase shifts/vector groups by using the zero key
Can operate independently of GSM or GPS reception with synchronisation
of the stored readings
Internal memory for 10 days of continuous operation
Li-Ion battery for 10 hours of operation
Data transfer via USB
Operation via LCD touch screen
Intuitive operating software
High voltage sensor with bidirectional wireless transmission to PVS 100
and direct visual signalling
Standard accessories
Phase verification system,
full set
»» 2 x PVS 100 incl. GPS outdoor unit
»» High voltage sensor with probe tips
»» Insulating rod 110 kV
»» 2 x cable set
»» Tripod for GPS module with holder
»» PVS probe for capacitive taps
»» Charger for HVS 120-36 and PVS probe
»» 2 GSM aerials with holder
»» 2 cases/trolleys for PVS 100
Phase verification system,
additional device
»» 1 x PVS 100 incl. GPS outdoor unit
»» High voltage sensor with probe tips
»» I nsulating rod 110 kV
»» Cable set
»» Tripod for GPS module with holder
»» PVS probe for capacitive taps
»» Charger for HVS 120-36 and PVS probe
»» GSM aerial with holder
»» 1 case/trolley for PVS 100
Recommended options
More products SEBAKMT
|
SEBA BPS 5000-D BURN AND PROOF TEST SYSTEM ON MEDIUM VOLTAGE CABLES BPS-5000D BPS500D BPS 5000D-VLF
• Easy-go single button operation |
|
SEBA KMT SEBALOG CORR MULTI-CORRELATOR LOGGER FOR WATER LEAK DETECTION AND LOCATION
• Correlation with up to 8 sensors at the same time |
|
SEBA KMT VFL CR-28..60 VLF TEST SYSTEMS FOR MEDIUM VOLTAGE CABLE TESTING
• VLF CR-28 up to cable series 15 kV |
|
SEBA KMT HVB-10 10KV CABLE FAULT LOCATION, STEATH TESTING AND PINPOINTING MEGGER HVB10
• Output voltage 0 … 10 kV DC, bi-polar |
|
SEBA KMT PVS-100 PHASE IDENTIFICATION TESTER FOR CABLE SELECTION
• Identifies the phase at all voltage levels in real time |
|
SEBA KMT EASYTEST 20KV VFL CABLE TESTER VERY LOW FREQUENCY
• simplified version of the standard VLF test |
|
SEBA KMT HPA35 HPA50 HPA58 HPA78 AC HIGH VOLTAGE HIPOT TESTING WITHSTANDING
• HPA 35, AC testing up to 35 kVrms |
|
SEBA KMT CDS CABLE DIAGNOSTIC SYSTEM FOR THREE PHASE IRC AND RVM DIAGNOSTICS
• Absolutely non-destructive condition evaluation of PE / XLPE / paper-oil insulated cable systems |
|
SEBA TELEFLEX VX CABLE REFLECTOMETER FOR FAULT LOCATION SYSTEMS
• Range : 20 m … 1280 km |
|
SEBA SWG 8-1000 SURGE UNIT HIGH VOLTAGE GENERATOR FOR CABLE FAULT LOCATING SWG8-1000
• Voltage Ranges : 0..2kV / 0..4kV / 0..8kV |