The GLC-9000, leakage current tester, is used to perform leakage current (or called touch current) tests on medical electrical (IEC 60601-1) and general purpose electric & electronic (IEC 60990) equipment. This tester engages with nine measurement networks (or called Measuring Device) to provide the simulation of human body while the EUT (equipment under test) is taking a leakage current testing in compliance with the specific standards or regulations such as IEC, UL, JIS...etc..

In order to provide a simple operation environment, the GLC-9000 equips with large TFT LCD touch panel to configure system as well as to present the measurement settings information and result simultaneously. Besides, there are 50 preset testing conditions, which conform to IEC60990 and other standards, for general electric equipment can be recalled to reduce the setting time. In addition, 30 sets empty memory are available for user defined setting.

A Meter mode is also available for the GLC-9000, it uses the measurement terminal (T1/T2) to measure voltage as the same way of ordinary voltmeter. During the voltage measurement, the SELV function (safety extra low voltage) is applicable to detect whether the voltage value between measuring points exceed the SELV setting.

Accesorii standard

GLC-9000 Leakage Current Tester

User manual x1, Power cord x2, Test lead (GTL-117) x2, Alligator clips x4(Red x2 / black x2), Foil probe x1

Optiuni recomandate

Accessories:

User manual x1, Power cord x2, Test lead (GTL-117) x2, Alligator clips x4(Red x2 / Black x2), Foil probe x1

Optional Accessory:

GTL-246 USB cable

Alte produse GW INSTEK

GOODWILL INSTEK GDM-400 & GDM-300

• 22000 Counts Auto/Manual Ranging (GDM-461)
• 4000 Counts Auto/Manual Ranging (GDM-397/398)
• 6000 Counts Auto/Manual Ranging (GDM-360)
• Capacitance, Frequency Measurement
• Continuity Beeper/Diode Test

GOODWILL INSTEK GPR-M SERIES

• Constant Voltage and Constant Current Operation
• Internal Select for Continuous or Dynamic Load
• Low Ripple and Noise
• Overload and Reverse Polarity Protection

GOODWILL INSTEK APS-1102A

• Arbitrary Waveform Power Output
• Power Amplifier of External Signal
• Measurement Functions: Voltage, Current, Power ,Frequency, Power Factor,CF,and Harmonic Current
• Capacitor Input Load Supported

GOODWILL INSTEK LCR-6000 SERIES

• Consecutive test frequency
• Basic accuracy : 0.05%
• Measuring speed up to 25ms (max.)
• Full frequency range or spot OPEN/SHORT

GOODWILL INSTEK MFG-2000 SERIES

• Earth Ground Isolation Design Among I/O Terminals and Instrument Chassis
• Frequency Counter : 150MHz, 8 bits
• AM/FM/PM/ASK/FSK/PSK/SUM/PWM Modulation
• USB Host/USB Device/LAN (MFG-22XX only)
• 4.3 Inch TFT Color Display

GOODWILL INSTEK AFG-3000 SERIES

• Wide frequency range from 1uHz to 80/50MHz
• High 200MSa/s sampling rate
• 16-bit Amplitude Resolution
• Output from any section of 1M-point-long waveform

GOODWILL INSTEK PEL-3000E

• OCP?OPP test Automation
• Max. Slew Rate: 2.5A/us
• Dynamic mode
• Protection: OVP, OCP, OPP, OTP, RVP, UVP
• Remote Sense

OSCILOSCOP ANALOGIC 2 X 50 MHZ GW INSTEK GOS-6051

• 50 MHz bandwidth
• 2 analog channels
• 1mV/div ~ 20V/div
• Cursor Measurement, 6 Digit Frequency Counter, 10 sets Memory for Front Panel Setting Save & Recall

GOODWILL INSTEK GPT-9600 SERIES

• Auto W-I or I-W Mode
• ARC Detection
• True RMS Current Measurement
• Zero Crossing Turn-on Operation

ANALIZOR SPECTRAL 9KHZ..3GHZ GW INSTEK GSP-930

• Frequency Range: 9kHz ~ 3GHz
• High Frequency Stability: 25ppb (0.025ppm)
• RBW: 10Hz ~ 10kHz in 1-3 steps, 10kHz ~ 1MHz in 10% adjustable steps
• Phase Noise: -88dBc/Hz @1GHz, 10kHz Offset
• Built-in Measurement Functions: Channel Power, N-dB bandwidth, OCBW, ACPR, SEM, TOI, CNR, CTB, CSO
• Built-in Spectrogram and Topographic Display Modes