The Extech MA200 Compact Clamp Meter has a 2,000 count LCD display with high accuracy for current measurements. It has a 0.9" (23mm) jaw size that accommodates conductors up to 300MCM. This meter has a continuity beeper and a diode test as well as the data hold feature and the max hold feature. Also, the MA200 has overload protection for all ranges, over range and low battery indicators. This Extech meter has autoranging with an auto power off function. The Extech MA200 Compact Clamp Meter comes complete with test leads, a carrying case and two AAA batteries.

� 2000 count LCD display

� High accuracy for Current measurements

� 0.9" (23mm) jaw size accommodates conductors up to 300MCM

� Continuity beeper and Diode test

� Data Hold, Max Hold

� Overload protection for all ranges

� Overrange and low battery indicators

� Autoranging with Auto Power Off

� Complete with test leads, case and two AAA batteries

Alte produse EXTECH

EXTECH 380400 BOXA DECADICA DE REZISTENTE

• Durable construction
• Case may be grounded separately
• 3 binding posts permit isolated substitutions
• 1% Resistance substitution from 1 to 11,111,110O
• Seven decade ranges of resistance
• Values can be set in 1O increments

EXTECH ET38 TESTER TENSIUNE SI CONTINUATATE

• Voltage detection range: 12 to 300V AC
• Continuity tester
• LED light indicator
• Includes built-in screwdriver tip, pocket clip, and two button batteries

EXTECH CO30: CO (CARBON MONOXIDE) MONITOR

• Alternately displays Carbon Monoxide (CO) concentration, Air Temperature, and Relative Humidity readings (cycles approximately every 6 seconds)
• Visible bright tri-colored (green, yellow, red) LED alarm indicator
• Adjustable audible alarm for readings exceeding one of the selected ranges: 25ppm, 30ppm, 35ppm, 50ppm, 100ppm or 200ppm
• ZERO Re-Calibration function
• Manual Temperature and Relative Humidity Compensation (adjustable)
• CO Calibration function in fresh air

EXTECH 407736 SONOMETRU CU 2 SCALE

• Provides 1.5dB accuracy
• Meets ANSI and IEC 651 Type 2 standards
• Two measuring ranges: 35 to 90dB (Low) and 75 to 130dB (High)
• Max Hold with reset button
• Built-in calibration check (94dB)

EXTECH MA410 CLESTE CURENT 400A AC + DETECTOR FARA CONTACT

• AC Current, AC/DC Voltage, Resistance, Frequency, Capacitance, Temperature, Duty Cycle, Diode and Continuity
• Integrated Non-Contact Voltage Detector with LED alert
• Compact size allows measurments in tight locations
• 1.2" (30mm) jaw size for conductors up to 350MCM
• Relative Mode for Capacitance Zero and Offset Adjustment

EXTECH EX505 MULTIMETRU DIGITAL INDUSTRIAL REZISTENT CU 11 FUNCTII

• True RMS DMM with 11 functions and 0.5% basic accuracy
• AC/DC Voltage & Current, Resistance, Capacitance, Frequency, Temperature, Duty Cycle, Diode/Continuity
• Dual sensitivity frequency functions (electrical/electronic)
• 1000V input protection on all functions
• 10A max Current

EXTECH CO15: CARBON MONOXIDE (CO) METER

• Dual LCD simultaneously displays Carbon Monoxide (CO) level and maximum CO reading taken from when the meter was powered on
• Long life electrochemical sensor
• Adjustable CO warning level at 25, 30, 35, 45, 50, 70, 100 and 200ppm (alarm is preset to 25ppm)
• Audible alarm when CO level reaches the warning set point level
• Choose from 3 calibration points: 0 (preset), 100, and 500ppm

EXTECH MO25 UMIDIMETRU TIP STILOU

• Easy-to-use one button operation
• Data Hold and Auto power off
• Battery level check on power-up
• Complete with protective cap, built-in pocket clip, and one AAA battery

EXTECH MN16A MULTIMETRU DIGITAL MINI

• Large easy to read digital display
• AC/DC Voltage & Current, Resistance, Capacitance, Frequency, Continuity, Diode Test, Type K Temperature and Duty Cycle
• Auto power off with disable feature
• Complete with two AAA batteries, general purpose Type K bead wire probe and test leads

EXTECH 382213 SURSA TRIPLA DIGITAL DE TENSIUNE CC

• Adjustable Voltage and Current output
• Easy snap terminals for fixed 5V/0.5A and 12V/1A outputs
• Constant Voltage or Current
• Current limiting indicator