AC/DC current: Clamp-on measurement of ac current up to 1400 A rms and dc current up to 2000 A without breaking the circuit
Highest safety rating: 600 V CAT IV power analyzer is rated for use at the service entrance
Accurate in noisy environments: Clamp meter performs even with distorted waveforms present on electronic loads with low-pass filter
Data logging: Identify intermittent faults by logging any power quality parameter for minutes, or over a month, including harmonics
Verify batteries: Direct measurement of dc ripple (%) for battery and dc systems
Troubleshoot harmonics: Analyze and log harmonics digitally or graphically
Inrush current: Capture and analyze nuisance tripping, from 3 seconds to 300 seconds
Easy to use: Easily confirm power meter setup with large backlit color display of waveforms and trends
3-Phase power: Built in capability for balanced loads
View graphs and generate reports: Use power analyzer with included Power Log software

Standard accessories

345 Power Quality Clamp Meter
Soft carrying case
Power Log software
Test leads
Alligator clips
Test probes
USB cable
International ac adapter / battery eliminator
Printed English language user manual
Multi-language manual CD

Recommended options

AC220 SureGrip™ Alligator Clip Set
TLK291 Fused test probe set
TP1 Slim Reach Test Probe (flat blade)
TP220 SureGrip™ Industrial Test Probes

More products FLUKE

FLUKE 6304/ 6304C AUTOMATIC RCL METER 50 HZ..100 KHZ

• 50, 60, 100, 120 Hz, 200 Hz to 20 kHz (100 Hz steps), 100 kHz test frequencies
• 0.1 % basic accuracy (0.05 % for PM 6304C)
• Easy to use, at-a-glance display

ESA710 ELECTRICAL SECURITY ANALYZER FOR TESTING MEDICAL EQUIPMENTS

• 5” Touchscreen with intuitive user interface
• Small, portable, ergonomic design with an integrated handle
• OneQA-enabled workflow automation eliminates need for laptop
• Wireless capability allows you to run test procedures in the field and automatically sync results

WIRELESS CURRENT CLAMP FLUKE CNX A3000

• True-RMS AC current measurements to 400 A
• 2% accuracy to 100 Hz, 2-1/2% accuracy to 500 Hz
• Memory recording up to 65,000 readings
• Backlit LCD display
• CAT III 600 V; IP42

INFRARED NON-CONTACT THERMOMETER FLUKE 61

• Bright laser beam provides easy targeting
• Display clearly supplies data at a glance
• Shock-absorbing holster increases ruggedness
• 0.2 °C (0. 5 °F) resolution up to 275 °C (525 °F)
• Backlight illuminates the screen in the dark
• Automatic sleep mode after 7 seconds extends battery life
• Alkaline batteries provide 4000 typical measurements

FLUKE 438 II MOTOR AND ENERGY QUALITY ANALYZER

• Measure key parameters on direct-on-line motors including torque, RPM, mechanical power and motor efficiency
• Perform dynamic motor analysis by plotting of motor derating factor against load according to NEMA/IEC guidelines
• Calculate mechanical power and efficiency without the need of mechanical sensors, just connect to the input conductors and you're ready to go
• Measure electrical power parameters such as voltage, current, power, apparent power, power factor, harmonic distortion and unbalance to identify characteristics that impact motor efficiency

FLUKE VT04 INFRARED THERMOMETER WITH INTEGRATED CAMERA

• take simultaneous visual images with the thermal heat map images that are accurately aligned close in
• Temperature measurement range -10 °C to +250 °C (14 °F to 482 °F)
• Infrared spectral band 6.5 µm to 14 µm
• Minimum focus distance 50 cm (19.6 in)
• Field of View 28° X 28°
• 4 GB Micro SD card

WIRELESS AC FLEXIBLE CURRENT CLAMPMETER FLUKE CNX I3000 IFLEX

• True-RMS AC current measurements to 2500 A
• 3% accuracy
• Memory recording up to 65,000 readings
• iFlex current probe allows you to get into tight, awkward spaces
• Backlit LCD display
• CAT IV 600 V, CAT III 1000 V

FLUKE 233 HANDHELD DIGITAL MULTIMETER 3.5 DIGIT

• 3.5 digit
• 6000 count
• 0.25% accuracy
• Remote Display
• Measure up to 1000 V ac and dc
• Measure up to 10 A (20 A for 30 seconds)
• 10,000 µF capacitance range
• Frequency to 50 kHz
• True-rms ac voltage and current for accurate measurements on non-linear signals

FLUKE 721 PRESSURE CALIBRATOR

• 16 PSI (1.1 bar) or 36 psi (2.48 bar) low pressure sensor
• 7 high pressure ranges including 100, 300, 500, 1000, 1500, 3000 or 5000 psi (6.9, 20, 24.5, 69, 103.4, 200, 345 bar)
• Ideal for gas flow calibration (custody transfer) applications
• Two isolated, stainless steel, pressure sensors with 0.025 % accuracy
• Pt100 RTD input for temperature measurement, (probe optional)
• Measures 4 to 20 mA signals
• Internal 24 V loop power supply can power a transmitter under test
• Measure up to 30 V dc, check 24 V loop power supplies

VOLTAGE CONTINUITY TESTER FLUKE T120

• LED Bargraph
• Display: Fluke T120: 3½ digit LCD
• Voltage test
• Optical and acoustical continuity test