The ISDN ANALYSER EIT 10 is a hand-held battery operated, multifunction - measuring instrument, intended for testing and qualifying Basic & Primary Rate ISDN. The EIT 10 provides a complete range of test functions for installation and maintenance of the ISDN. In the simulation measuring modes, the EIT 10 can be used at different reference points to check the functions of the ISDN. In monitor mode, the EIT 10 can monitor B-channel voice and D-channel signaling. It displays and records the decoded D-channel data. The EIT 10 is the ideal solution to find out and solve the problems arisen during the operation of the ISDN. The analyser can function as a telephone handset for performing in-service talk/listen or it can monitor voice quality and tones.

Features:

• BRI TE and NT simulation, monitoring

• PRI TE and NT simulation, monitoring

• Dual U interface for troubleshooting between the NT and the Exchange

• B-channel voice and D-channel signaling monitor

• EDSS1, V5.1/V5.2, QSIG, SS7 protocols

• Analysis of CAS (R1,5; R2)

• Automatic test of the supplementary services: CLIP,CLIR, COLP, COLR, CFU, CFB, CFNR, AOC, DDI,SUB, UUS

• Physical Layer testing

• Power feeding measurements with external adapters

• BERT bit error test with evaluation in accordance to G.821 / G.826

• Large store-recall memory for test results

• PC software for analysis of signalling data and control

• Selectable English or Russian languages

• LED indicators showing status of line signal

More products ELEKTRONIKA

XDSL LINE QUALIFIER ELQ 2+

• TDR for fault location
• Load coil detection facility
• DC-AC bridge option
• 2.2 MHz frequency range for fix-frequency and spectrum measurements
• Longitudinal voltage protection

2,4 MHZ LEVEL TEST SET ET 91

• Psophometer
• Autmatic End to End Measurements
• High Resolution Spectrum Analyzer
• Measuring Bridge
• Memory Locations for Test Setups

6 MHZ LEVEL TEST SET ET 92

• Comfortable End to End Measurements
• High Resolution Spectrum Analyzer
• USB Ports for Result and Setup Transfer
• Memory for Test Setups

CABLE FAULT LOCATOR EFL 10

• Loop resistance measurement
• Resistance difference measurement
• Mutual capacitance measurement
• Conductor-shield capacitance measurement
• Break and split measurement
• DMM functions

VDSL LINE QUALIFIER ELQ 35

• Service Telephone Function
• PC Supported Spectrogram
• Long Time Micro Interruption Measurement
• Long Time Impulse Noise Measurement

TIME DOMAIN REFLECTOMETER ELEKTRONIKA ETDR 10A-1

• TDR for balanced cables
• Easy to operate
• Automatic detection of the fault
• Small size, suitable for using in the field at different weather conditions
• Widest range in a hand-held cable fault locator up to 16 km

ISDN ANALYSER EIT 10

• BRI TE and NT simulation, monitoring
• PRI TE and NT simulation, monitoring
• Dual U interface for troubleshooting between the NT and the Exchange
• B-channel voice and D-channel signaling monitor
• EDSS1, V5.1/V5.2, QSIG, SS7 protocols
• Analysis of CAS (R1,5; R2

TELEPHONE & EXCHANGE TESTER ETT 10

• Hand-held programmable instrument with microprocessor control
• Testing of subscriber lines, exchanges and telephone sets
• Hand-held programmable instrument with microprocessor control
• Ring generator for testing telephone sets
• Battery for feeding the telephone line with DC current

XDSL SERVICE TESTER & TROUBLESHOOTER EX 30M

• Transmitted power
• Line attenuation
• Line alarms (LOS, LOF, LOP, LOM)
• Line errors (FEC, CRC, HEC)
• Ping test / trace route

UNIVERSAL COPPER QUALIFIER ELQ 30A+

• Analogue measurements on leased or switched circuits 20 Hz to 20 kHz
• Analogue-to-analogue measurements on PCM systems
• Loop holding and dialling (pulse or DTMF) for dial-up circuit testing
• Built-in loudspeaker and microphone, service telephone
• In-service talk/listen and voice monitoring facility