Pulse Circuit Trainer ED-6400

Code: ED-6400


 

Datasheet PDF, 0.72 Mb

Description

SIGNAL SOURCE & DC POWER SUPPLY(NO-6409)

  • Output Frequency : 100Hz, 1kHz
  • Output : 0~10Vp-p(Sine and square wave)
  • One-Shot Output : Positive and negative pulse
  • Logic Switch : 2-switch control
  • Indicators : 3-LED(built-in Driver Amp)
  • DC Output : +12V(0.5A), -12V(0.3A)
  • DC Protection : Overload Protected
  • Input Voltage : AC 220V, 50/60Hz
  • Dimension : 260(W) x 64(H) x 166(D)mm

 

MODULES & SYSTEM CASE

  • No. of Experimental Modules : 8ea
  • Module Dimension : 250(W) x 64(H) x 166(D)mm
  • System Case Dimension : 550(W) x 200(H) x 461(D)mm
  • System Weight : Approx. 16kg

 

ACCESSORIES

  • Patch Cord : 1set
  • AC Power Cord : 1ea
  • Experimental Manual : 1ea
  • Experimental Rack(MR-8) : 1ea

 

EXPERIMENTAL RACK(MR-8)

  • Module Mounting Capacity : 8ea
  • Power Supply Bus(DC) : 2-Line(+, -) and GND
  • Dimension : 1100(W) x 640(H) x 300(D)mm
 

More products ED

PC BASED BASIC ED-1420

• 15 experimental modules for basic electricity/electronics and analog & digital circuits
• Capable of real time measurement on PC by linking it to CBIS-1400 model.
• By connecting PC to the Docking station, contact control is implemented on MMI(HMI) based software
• Report on experimental results & electronic manual on PC

 

LOGIC TRAINER ED-1100A

• Unique logic cards(TTL/CMOS)
• Internal pulse outputs
• 3-stage Logic Monitor
• BCD indication

 

SMALL DESKTOP TYPE PLC TRAINER ED-4260MD

• Small desk type structure for space optimization
• Built-in DC power supply for convenience
• Handy experiments on the basic and application programming commands
• Base structure capable of expansion by mounting the special modules

 

NETWORK TRAINING SYSTEM SERIES ED-NET4-X

• Step by step courses on the networks theories to train the engineers
• CISCO Router based training will help obtain CCNA, CCNP, CCIE certificates
• Functions and characteristics of network system(LAN Card, Router, L2 Switching Hub, L3 Switching Hub)
• 19Rack type structure for effective network configuration
• Optimized learning system for the Router based on one on one training(OPTION)

 

MOTOR / GENERATOR TRAINER UNIT MG-5216

• RIM’s no-load power factor and load power factor
• Load characteristics of separately excited DC shunt-wound generator
• No-load saturation characteristics of generator
• DC shunt-wound generator’s loss and power factor

 

FUEL CELL TRAINER ED-9741

• Testing of load for maximum four fuel cell at the same time
• Removable type of electrical dissolution and fuel cell from main body
• Monitoring through LabVIEW program

 

CONVEYOR CONTROL SIMULATION UNIT CU-4001

• Belt-type conveyor simulator
• Control Modes : manual or automatic by programmable Logic Controller
• Three photo sensors and two motion solenoids

 

NEW & RENEWABLE ENERGY TRAINER ED-9720

• Conversion experiments on the produced energy(power production/processing)
• Characteristics of Solar Cell module’s voltage and current
• Alarm beep for wrong wire placement
• Voltmeter and ammeter as included for measuring AC and DC
• Control by PC and waveform and graph output

 

DC MOTOR/ GENERATOR MG-5211

• Load characteristics of DC compound motor
• Cumulative compound and differential compound characteristics
• Generator’s rotating speed and output characteristics
• Loss and efficiency of DC compound generator

 

LON DEVICE DEVELOPMENT KIT ED-5960

• Home network based experiments suitable for ubiquitous computing
• Integrated ubiquitous device using ZigBee/RFID and finger print recognition
• Designed to help develop home network on the ground of Lon Protocol
• Equipped with each PLC module(Power Line Communication) for home network
• Related experiments through Neuron C and MICOM programming